DIY garden composter

avatar

As we have a garden of our own, we're getting some garden waste we would need to get rid of. In addition to this we have a bokashi composter in our kitchen which would need a post-composting spot, where we're mixing the compost in some old soil. The fresh food compost mass from the bokashi has so much nutrients it's not good for plants, so it needs to be mixed in some old soil.

So I decided I could build a simple but sturdy post-composter which can also be used for the ton of leaves we get in our garden every fall. Every god damn fall.

image.png

The plan is simple. We kill Batman The composter is 80 cm wide, 44 cm deep (40 cm long wood on sides + 2*2 cm because the long wood is 2 cm wide) and the height was to be determined when I was building this. Ultimately it was approx. 70 cm high, but I didn't know it at this point.

I had some old impregnated wood and bought 20 meters of new wood for this project.

Kompostori  1.jpg

The bottom piece is made from old impregnated wood I had. The longer pieces are 80 cm and the shorter ones were cut to make sure the total depth is approx. 44 cm.

As it still contains food compost, it's good to add a metal net in the bottom. The bottom is otherwise open to make sure that the microbes and worms from the soil can reach the compost. The net was attached by wide headed screws. To make sure rodents will not dig their way in from the sides, remember to use enough screws.

Kompostori  2.jpg

I built the first layer of the composter and attached the bottom piece with screws in it.

Kompostori  3.jpg

I built only the first layer and then added the first bar on the inside. There's 3 screws holding it, so it will not fall down and will allow me to start building the composter around it.

Kompostori  4.jpg

To make the construction simpler, the screws are pre-screwn in the wood.

Kompostori  5.jpg

It's easy to lift the pre-screwed wood (haha.. it's screwed) on it's place and screw it. I'm only attaching it from one side to make sure I can adjust the height easily.

Kompostori  6.jpg

I attached 6 layers of wood and as the wooden bar used was longer than it needed to be, I measured how high it should be. I held the 7th layer piece on the side and held a piece from the future lid to see the required height of the support bar.

Kompostori  7.jpg

The bar was cut. Not straight but fast.

Kompostori  8.jpg

Then I attached the 7th layer. The support bar is now left lower than the side wall is, but this is to leave some room for the lid. The lid will be restin on the side bars.

Kompostori  9.jpg

I cut the remaining bars to same height and added them in each corner. It was quick to attach the screws on the second bar too.

Kompostori  10.jpg

One side ready, but now already at a good phase.

Kompostori  11.jpg

The second wall was added in very similar way than the first one, but now I could attach both sides on the same time. This could be possible for most people too if you know how high composter you'll build. I didn't know so I had to see it before I knew what I want.

Kompostori  12.jpg

When attaching the longer side, remember to pre-screw the screws further away from the end of the wood. If you're not pre-screwing them, this is not an issue.

Kompostori  14.jpg

First long side built. This is also a real fast job.

Kompostori  15.jpg

Now you can easily put the composter to lie down and attach the remaining few pieces.

Kompostori  17.jpg

The remaining pieces were used to build a lid. One piece had to be cut in half as otherwise it would have been too wide, but it was no issue.

Kompostori  18.jpg

I used two remaining pieces of the wooden bar I had and attached the lid pieces together.

Kompostori  19.jpg

As I wanted proper handles for this, I used regular timber to make two handles. I used a single 15 cm wide piece of timber and used a jigsaw to freely cut a handle shaped piece of it. The only markings I made was how far I can cut and how much space I'll need for my hands on the handle.

I've never made handles before so I had no idea what to take in consideration.

Kompostori  20.jpg

The shape was pretty simple, I wanted the ends to be flat and long so it'd be easy to screw. The hole in the middle has to be large enough that it's easy to open even with gloves on.

Kompostori  21.jpg

As the first handle was good, I drew a rough sketch to get the second handle as similar as possible.

Kompostori  22.jpg

The jigsaw is not actually moving in the photo, I just wanted to get a photo of the work.

Never use power tools and take photos the same time.

Kompostori  23.jpg

To give a finishing touch to the handles, some sanding paper will do wonders. It'll help to get the rough edges off and makes them pleasant to touch.

Kompostori  24.jpg

I'm doing my best to be humble, but I think this looks nice.

Especially as I'm actually quite crap in woodcrafts.

Kompostori  25.jpg

The compost is finished. Now it's just waiting to be used and I'm hoping it'll stay in good shape for years to come.



0
0
0.000
2 comments
avatar

Nice work!!! you are very skilled with the wood man

0
0
0.000
avatar

Congratulations @apsu! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s) :

You distributed more than 21000 upvotes. Your next target is to reach 22000 upvotes.

You can view your badges on your board And compare to others on the Ranking
If you no longer want to receive notifications, reply to this comment with the word STOP

Do not miss the last post from @hivebuzz:

Introducing HiveBuzz Shop - Offer gifts with your favorite badges
Support the HiveBuzz project. Vote for our proposal!
0
0
0.000