Capsula de escudos Apex Legends/ Apex Legends Shield Capsule

avatar
Hola makers de Hive soy Nitsu y me gustaría mostrarles el proceso que utilice y algunos tips para armar la capsula de escudos del Apex legends.

Hi Hive makers I'm Nitsu and I would like to show you the process I used and some tips to build the Apex legends shield capsule.

Gif (2).gif

Este archivo se encuentra gratis en Cults3D y lo imprimí porque ya hace algunas semanas fue el cumpleaños de un amigo y quería tener una atención con él. Así que pensando en que podía regalarle se me ocurrió hacer la capsula del Apex Legends y dentro colocarle algunos caramelos y chocolates.
This file is free in Cults3D and I printed it because some weeks ago it was a friend's birthday and I wanted to give him some attention. So thinking about what I could give him I thought of making the Apex Legends capsule and put some candies and chocolates inside.

Gif (1).gif

Comencé ordenando y separando algunos archivos STL debido a que venían todos juntos y era imposible imprimirlos de esa manera. Imprimir todas las piezas blancas, por un lado, luego las azules y por ultimo los detalles en color cobre de esta manera logramos optimizar los tiempos y hacer tantos cambios de color que podrían provocar obstrucciones en nuestras maquinas.
I started by sorting and separating some STL files because they were all together and it was impossible to print them that way. Printing all the white pieces on one side, then the blue ones and finally the copper colored details in this way we were able to optimize the time and make so many color changes that could cause obstructions in our machines.

20220210_190323.png

Gif (5).gif

En las piezas blancas curvadas utilice alturas de capa de 0.2 o 0.1 mas que nada para que no se noten las capas y quede todo mucho mejor, además de utilizar soportes para facilitar la impresión.
In the curved white pieces use layer heights of 0.2 or 0.1 more than anything else so that the layers do not show through and everything looks much better, in addition to using supports to facilitate printing.
20220210_190345.png 20220210_193212.png
Aproximadamente fueron más de 20 horas de impresión totales y una vez tuve todas las piezas uní la tapa blanca con la base resacada, en un principio no entraba por las tolerancias, pero un truco que aprendí con el tiempo fue calentar las piezas con una hornalla, sin calentarlas tanto para no arruinar las piezas, y haciendo presión logre que encastraran correctamente espere a que enfrié y quedaron perfectamente unidas.
Approximately there were more than 20 hours of total printing and once I had all the pieces I joined the white cover with the resacada base, at first it did not fit because of the tolerances, but a trick I learned over time was to heat the pieces with a stove, without heating them so much so as not to ruin the pieces, and making pressure I got them to fit correctly, I waited until it cooled and they were perfectly joined.
20220210_205519.png 20220210_205511.png

20220210_195017.png

De igual manera la rosca no cumplía su función así que utilizando el mismo método fui calentando la rosca y lentamente logrando que funcionara de forma correcta.
In the same way, the thread did not fulfill its function, so using the same method I was heating the thread and slowly getting it to work properly.

20220213_160533.png

Con pegamento epoxy fui uniendo los rebordes blancos con las piezas color cobre. Los logos con forma de rayo costaron un poco mas debido que las rebabas de la pieza no permitían un buen encastre así que toco lijar un poco al mismo tiempo que use la técnica de calentado para que encastre, una vez lo logre también aplique pegamento epoxy transparente para dejarlo fijo en su lugar.
With epoxy glue, I was joining the white edges with the copper-colored pieces. The lightning shaped logos cost a little more because the burrs of the piece did not allow a good fit so I had to sand a little at the same time that I used the heating technique to make it fit, once I achieved it I also applied transparent epoxy glue to leave it fixed in place.
20220226_163839.png 20220226_163846.png 20220226_163857.png

20220226_163946.png

Una vez tenia los volúmenes principales unidos empecé a pegarlos entre si la base con el cilindro con agujeros, el cuerpo central y los detalles de color cobre ya para este punto tenia todo listo, verifique algunos detalles como que todo haya quedado centrado y bien unido.
Once I had the main volumes together I started to glue them together, the base with the cylinder with holes, the central body and the copper-colored details, and at this point I had everything ready, I checked some details such as that everything was centered and well united.
Deje unas imágenes del objeto dentro del juego para los que no lo conoces y puedan ver las similitudes o diferencias con el objeto impreso.
Leave a few images of the object inside the game for those who do not know it and can see the similarities or differences with the printed object.
Captura de pantalla (1592).png Captura de pantalla (1594).png


0
0
0.000
4 comments
avatar

AAAA Me encanta! Se la voy a pasar a mi novio que es jugador de APEX!

0
0
0.000
avatar

Gracias @chereside tenia miedo cuando empecé pero la verdad que logre llegar a un resultado final muy bueno

0
0
0.000
avatar

Pues te quedo genial! esta chulisimo

0
0
0.000
avatar

Muchísimas gracias podes ver mas trabajos míos en mi Instagram comercial @nit_3dprinting

0
0
0.000