Motorola e7 Plus Disassembly Tutorial / Tutorial desensamble Motorola e7 Plus - [En-Es]

avatar

▶️ Watch on 3Speak





111.png


content sources
- Translation of the text:https://www.deepl.com
- Separator taken from:Here
- Photo and video:Picsart pro. YouCut. Samsung Galaxy j6 plus.
- Source and authorship of content:@josuerr29
- Creation of gift:https://www.canva.com.
- Video intro by @josuerr29app YouCut.
- Music of the video Without copyright:soundcloud
Logo 1Design by https://studio.3espeak.tv
Logo 2Design by https://hive.blog
Logo 3Design of the geek zone meal
Equipment used to record the videoMotorola e7 Plus
Recording equipmentSamsung j6 +
Setup for recordingTripod for can-i820

Ingles


Hello dear family Howdy Here I show you a disassembly of a device. This is the Motorola e7 Plus.

On other occasions I have brought me these motorola so I know how to disassemble them, however this is the first time I disassemble this equipment and I bring it to you so you know how to disassemble it.

This equipment came to my workshop for the following fault, and is that it showed that it was charging but it was simply discharging the battery and it seemed that when I connected it discharges faster, it was a little difficult fault and could be the charging pin or many other things.

The customer told me that he wanted it fast so I had to check the super fast, and now I show you the disassembly of the equipment.

To do it all I used were two pieces of x-ray plate spatulas, and a slotted screwdriver that's what I'm going to show you guys and I'll start with the disassembly.

Process

To begin with, all we need to do is put the x-ray spatulas between the bezel of the unit and the case, little by little and very carefully, and then move it all around the sides of the unit, putting pressure on it and lifting it up. This must be done very carefully.

111.2.jpg

After you have done this you have to go and press a little bit of pressure on the casing towards the outside, however you have to realize that it is sticky and this is going to be a little tricky. The strategy that I used was that when I lifted the housing a little bit I used the same spatula to cut the glue that did not let you separate the housing and so carefully I managed to separate the entire housing.

111.2.jpg

After I managed to do it, I have to do it very carefully because the Flex of the fingerprint had not been detached, if I Alaba with force I could break it before being able to remove the Flex of the fingerprint. Then I have to remove all the screws of the protective backover of the plates, and there I began to remove each of the screws and so I could lift the protective backover, when I managed to do it I could lift the flex of the fingerprint, and finally be able to remove the entire casing there. After doing this I had the main board uncovered. Now I only had to remove the screws from the bottom plate of the charging pin to remove the protective plate of the charging pin and so I did I managed to uncover then each Flex of the equipment.

DU.jpg

With great care to lift the main board and the charging plate of the phone first had to lift each Flex and remove all the screws that tightened the plate, all this very carefully, the Flex are those of the screen, those of the power button, the battery, the charging pin, and so when I could separate these Flex I could freely remove the two plates and this was what I did.

After having done all this I could consider the device completely disassembled and work completely with the charging pin.

111.11.jpg

In another video I will show you how to repair the charging pin of this unit.


Español


Hola querida familia Qué tal Aquí les muestro un desensamble de un equipo. Este es el Motorola e7 Plus.

En otras ocasiones me han traído estos motorola así que se como desarmarlos, sin en-embargo esta es la primera vez que desarme este equipo y te lo traigo para que tú sepas como desarmarlo.

Este equipo llegó a mi taller por la siguiente falla, y es que mostraba que estaba cargando Pero simplemente se estaba descargando la batería y parecía que cuando lo conectaba se descarga más rápido, era una falla poco difícil y podía ser el pin de carga o muchas otras cosas más.

El cliente me dijo que lo quería rápido así que yo tenía que revisar los súper rápido, y ahora te muestro el desensamble del equipo.

Para realizarlo lo único que utilice fueron dos pedazos de espátulas de placas de rayos x, y un destornillador de estría eso es lo que le voy a mostrar muchachos y comienzo con el desarme.

Proceso

Para comenzar lo único que necesitamos es meter las espátulas de rayos x entre el bisel del equipo y la carcasa poco a poco y con mucho cuidado y luego ir trasladándola por todo los lados del equipo, haciendo presión levantándola. Esto lo debes hacer con mucho cuidado.

111.2.jpg

Después de hacer esto tienes que ir hablandando con un poquito de presión en la carcasa hacia afuera sin embargo tienes que darte cuenta que está tiene pega y esto va a ser un poco complicado. La estrategia que yo utilice fue que cuando levanté un poco la carcasa utilice la misma espátula para ir cortando la pega que no te dejaba separar la carcasa y así con mucho cuidado logré separar toda la carcasa.

111.2.jpg

Luego de lograr hacerlo, tengo que hacerlo con mucho cuidado ya que el Flex de la huella no se había despegado, si yo lo Alaba con fuerza podría romperlo antes de poder quitar el Flex de la huella. Entonces tengo que quitar todos los tornillos del backover protector de las placas,y alli comencé a quitar cada uno de los tornillos y así pude levantar el backover protector, cuando logré hacerlo ya pude levantar El flex de la huella, y por fin poder quitar toda la carcasa de ahí. Después de hacer esto ya tenía la placa principal descubierta Ahora solo correspondía sacar los tornillos de la placa de abajo de la pin de carga para poder quitar la placa protectora del pin de carga y así lo hice logré descubrir entonces cada Flex del equipo.

DU.jpg

Con mucho cuidado para poder levantar la placa principal y la placa de carga del teléfono primero tenía que levantar cada Flex y quitar todos los tornillos que apretaban la placa, todo esto con mucho cuidado, los Flex son los de la pantalla, los de el botón de encendido, los de la batería, los del pin de carga, y así cuando yo pude separar estos Flex Ya podía libremente sacar las dos placas y esto fue lo que realice.

Después de haber realizado todo esto ya podría considerar el equipo completamente desarmado y trabajar completamente con el pin de carga.

111.11.jpg

En otro vídeo te mostraré Cómo reparar el pin de carga de este equipo.

He realizado este post siguiendo algunas de las recomendaciones de @cryptoalvirin

fuentes del contenido
- Traducción del texto:https://www.deepl.com
- Separador tomado de:Aqui
- Foto y video:Picsart pro. YouCut. Samsung Galaxy j6 plus.
- Fuentem autoría del contenido:@josuerr29
- Creación de gift:https://www.canva.com.
- Intro del video realizada por @josuerr29:app YouCut.
- Musica del video Sin derecho de autor:soundcloud
Logo 1Diseño de https://studio.3espeak.tv
logo 2Diseño de https://hive.blog
Logo 3Diseño de la cominida de geek zone
Equipo usado para grabar el vídeoMotorola e7 Plus
Equipo de grabacionSamsung j6 +
Setup de grabacionTripode para camaras can-i820

FUkUE5bzkAZT3HzV5tJDiU2ik81PCd4JCyhWnRcDN8XJsVFY3UNB8DCUemLnQEZEeADjVAdf8Z8maUfpDrh6asa4EGhWHae9vSiobbCkyNHCP6fu7veDbC9RajFzQys3FEZ3F9mDVsaxMxKvFzXjpyW7hGqzbuesRUtE.png

@josuerr29.gif





▶️ 3Speak



0
0
0.000
6 comments
avatar

Amigo! Como siempre agradecido porque traigas un poco de tu trabajo acá a la #Geekzone, siento que voy a salir arreglando celulares dentro de poco jaja. Igual veo que es un trabajo tremendamente delicado, o por lo menos así lo demostraste en el video. Increíble, felicidades, ojalá yo supiera hacer éste tipo de trabajos, es excepcional y muy útil. Ah por cierto, me contagiaste el bostezo jaja.

Con respecto al post, MUCHISIMAS GRACIAS de verdad por seguir mis sugerencias, estoy muy contento y se ve una clara mejora con respecto al anterior, felicidades también por eso!

Una sola pequeñisima y minúscula corrección, si te gusta poner títulos en inglés y español no agregues la etiqueta ES-EN al final ya que es redundante o en todo caso coloca el título en inglés y ahí si colocas la etiqueta.

Saludos amigo, pa delante!

!LUV

0
0
0.000
avatar

Muchas gracias a ti hermano por los comentarios hechos por la ayuda recibida fueron de mucha utilidad siempre tratando de mejorar y aumentar gracias por todo gracias por ese último que me diste voy a aplicarla y bueno trato de hacerlo lo más sencillo posible para que todos vean que no es tan difícil

0
0
0.000
avatar

Excelente mi brother, el post de hoy (hablando del escrito) te quedó muy bueno, te felicito !

Yo tengo ahí un Moto g8, casi arreglas mi celular(? va en teoría lo tengo guardado y estoy usando otro, pero los moto nunca me han fallado. Son bien sólidos en todos los áspectos.

Saludos bro, que estés muy bien! Gracias por los tutos que nos tráes para que quien lo necesite, lo pueda utilizarrr!

!PGM

0
0
0.000
avatar

Sent 0.1 PGM - 0.1 LVL- 1 STARBITS - 0.05 DEC - 15 SBT tokens to @bananasfallers, @josuerr29

remaining commands 6

BUY AND STAKE THE PGM TO SEND A LOT OF TOKENS!

The tokens that the command sends are: 0.1 PGM-0.1 LVL-2.5 BUDS-0.01 MOTA-0.05 DEC-15 SBT-1 STARBITS-[0.00000001 BTC (SWAP.BTC) only if you have 2500 PGM in stake or more ]

5000 PGM IN STAKE = 2x rewards!

image.png
Discord image.png

Support the curation account @ pgm-curator with a delegation 10 HP - 50 HP - 100 HP - 500 HP - 1000 HP

Get potential votes from @ pgm-curator by paying in PGM, here is a guide

I'm a bot, if you want a hand ask @ zottone444


0
0
0.000
avatar

Hermano tengo casi 8 años reparando teléfonos y desde qué comencé la verdad los Motorola son excepcionales demasiado bueno Y ese g8 es muy muy buena Gracias por comentar hace por pasarte amigo Espero estés muy bien y Espero seguir nos encontrando aquí

0
0
0.000