Electrical device safety: How to avoid overload and short circuit

In this world of current technology, we are dependent on electricity. We cannot do anything without electricity and electricity is a necessity for us everywhere. Now it is possible to run bikes and all kinds of vehicles with electricity for our daily life. We carry out every activity of the day with the help of electricity, even the device you have in your hand also has the contribution of electricity. Without electricity, our smartphones, laptops, computers, various motorbikes for our transportation, everything depends on electricity. So since we are dependent on electricity, we must work to save that electricity without wasting it and prevent the wastage of electricity.

For example, when we leave the bedroom after waking up in the morning, we must immediately switch off the fan light or table lamp. When we finish the work in the bathroom, we must turn off the lights inside it. Especially, we will not use electric stoves for unnecessary reasons and we will always turn them off properly after cooking and we will all work together to prevent electricity waste.

But above all, we should keep one thing in mind. The more useful something is, the more likely it is to cause harm. In that case, it is our responsibility to protect our electrical devices such as mobile phones, laptops, computers or monitors, whatever they may be. I want to tell you about the smartphone in your hand.

Suppose your smart phone is fast charging and it takes 2 hours to charge. Now you can charge your smartphone very easily and due to your laziness you go to sleep at night and put your smartphone on charge and sleep. Where it takes only 2 hours to charge your phone, before going to sleep at night you put your phone on charge and sleep and your phone remains charged for 12 hours. What is the possibility here?

In case of overload charging, your device can explode and there is a possibility of serious fire and your device can be permanently damaged. Not only the damage will go on your device, but also your house can catch fire and the surrounding areas can be burnt down in case of electrical fire.

Source

So we should always keep one thing in mind. We should be careful when using all the devices that we use and if they are electrical devices, then we must be careful. Because if we are not careful, they will short circuit and damage our devices, just like our surrounding houses can burn and we can be damaged. In that case, we may have to pay a large fine.

Short circuit is a very risky thing for our lives. Especially when we use electrical connections in our homes and enjoy various facilities. In order to enjoy the facilities, we only use electrical connections as we wish and in that case, no smart technician is needed.

I have seen many times, there are many of us who connect various electrical connection lines on our own without taking the advice of an electrical technician. As a result of connecting all these lines, sometimes all the circuits get burnt and we face huge losses. Especially, these accidents happen more in shopping malls or homes. When an electrical connection is made without a technician and when excess electrical pressure is applied to that connection, then due to overload, short circuit occurs and electrical fire accidents occur there. Which is very risky for our lives.

Source

I want to inform you about one thing in the third place. Suppose there is a transmitter in your area and electricity is supplied to your area from there. But if 100 people in that entire area are supplied with electricity through the transmitter and if there are 110 users there, what is the solution??

Of course, the 100 volt transmitter has to be changed and a 120 volt transmitter has to be used there. Because it is possible to provide electricity service to only 100 customers using a 100 volt transmitter. In that case, if electricity service is provided to 1120 customers using a 100 volt transmitter, then the matter reaches the point of overload. That is, it is never possible to provide electricity service to 120 customers with a 100 volt transmitter. If that is done, then the transmitter may burst and an electric fire may spread to the entire area and a serious accident may occur. In that case, what should we do??

Of course, electrical overload cannot be given. As much power can be applied and as much load can be given as much load. Because no one can ever carry power according to his own capacity. The matter contributes similarly in the case of electricity.

So when using electrical devices, we must protect them from hands. When using electricity, we must remove it and we must be aware when using electrical devices. Each line must be repaired cleanly by a skilled technician and never short-circuit and fire accidents can not be caused. Especially, it has become a very important matter to be careful in our use of electricity.

Posted Using INLEO