Building A New Workstation PC Part 5 | Memory
Welcome back to my series about the ancient art of building a PC. This 'installment' will be sure to set you on the edge of your seat! In case you missed my previous posts on the subject (1-4), please do check them out.
It's great to have a lot of memory, but slow memory can be a bottleneck in a high performance system with multiple cores and multiple memory channels. The latest and greatest and fastest memory you can currently buy is 5000MHz, but we'll settle for a spritely 3200MHz.
If you are looking for 64GB DIMM of DDR4, the most options available involved sets of 4 DIMMs at 16GB. If your motherboard only has 4 DIMM slots, filling them all up with 16GB will prevent you from maxing out your memory. My particular motherboard (see previous post) supports up to 128GB. If you are also looking for higher performance memory, such as 3200MHz, your choices as a consumer/gamer are even more limited from mainstream sources such as Amazon.
Luckily I found this set of 2x32GB made by Corsair for a mere $299, quite the bargain (sarcasm). This memory ticked all the boxes I was looking for including:
* 3200MHz for high performance
* 32GB per stick for upgradeability
* No disco LED lighting for sanity
* Low profile and heat sinks for cooling/air flow
The memory sticks have a heat sink attached to the memory chips. This helps them dissipate heat. They are DDR4 form factor, so they can only be mounted in the memory slot in one direction. This is because one set of gold pins is longer in the other. I have seen many times where people have tried to install them backwards, only to realize they can't get their PC to boot. It is a good idea to ensure the notch on the memory properly aligns with the keyed memory slot, and the DIMM is properly seated.
My particular motherboard supports dual channel operation, meaning there are two distinct paths for memory to communicate with the CPU. This effectively doubles your memory data transfer, if they are installed correctly.
Before you actually install your memory, especially if you use less than the maximum number of DIMMS, you should verify in the motherboard manual the order in which they should be installed. Failing to do so could cause your memory to not be recognized properly, or force your system to operate in single channel mode.
Here's a view of our mounted motherboard with RAM slots waiting to be populated with memory. Make sure the little levers on either side are spread apart before inserting the RAM (is it getting hot in here?). Again, it is critical to ensure the notch on the memory stick lines up with the key in the memory slot. Once the memory is installed, firmly press down until you hear a click. At this point, both levers should be closed. If should should happen to open the levers again, it will cause the DIMMs to eject from the slot, so be careful.
Here we have the memory installed into each channel as per the documentation. It's easier to notice now how unintuitive the install pattern is, which is why checking documentation is always recommended.
Thanks for viewing. In the next post we'll install the CPU, since it turns out I had a decent amount to say about the memory install.
Posted from my blog with SteemPress : https://joshman.com/building-a-new-workstation-pc-part-5-memory
Looks like a lovely beast of a machine. I await with baited breath your CPU selection. :-)
Haha, don't get your hopes up too much! ;)
In my short stay in the US, to get a certain job I had to prove I could build PC's (only in fucking America, the land of non-trust). I was offered it but turned it down. That was on top of doing a standard IQ test.
PC's were more of a pain in the arse to build then, and are easier now. It was rare you put one together and it worked first time.
They've made it pretty easy and standardized. My first job out of the Air Force was at a little computer store, and I had to frankenstein all sorts of stuff together to build stuff to sell. This was before the days of ATX and USB even.
ISA and EISA? I remember them all, but don't really want to.
Today I loathe building PC's, the one I have was built from parts but the building bores me to death.
I think the novelty wore off a long time ago.
Haha, oh yeah! When 1 MB of memory was $80, and hard drives were a lot less than a gig.
I'm hoping this one will be good for 10 years!
64GB ram is already a lot.
I imaginevyou are skimpung om the LEDs because you have a giant disco ball hanging in your office.
Virtualization my friend. I'll be installing VMWare Workstation, and will probably need to max it out when it's all said and done.
This post has been voted on by the SteemSTEM curation team and voting trail. It is elligible for support from @minnowbooster.
If you appreciate the work we are doing, then consider supporting our witness @stem.witness!
For additional information please join us on the SteemSTEM discord and to get to know the rest of the community!
Please consider using the steemstem.io app and/or including @steemstem in the list of beneficiaries of this post. This could yield a stronger support from SteemSTEM.
!BEER
for you
View or trade
BEER.Hey @joshman, here is a little bit of
BEERfrom @eii for you. Enjoy it!Learn how to earn FREE BEER each day by staking.
You have been curated by @hafizullah on behalf of Inner Blocks: a community encouraging first hand content, with each individual living their best life, and being responsible for their own well being. #innerblocks Check it out at @innerblocks for the latest information and community updates, or to show your support via delegation.
Hi @joshman!
Your post was upvoted by @steem-ua, new Steem dApp, using UserAuthority for algorithmic post curation!
Your UA account score is currently 3.728 which ranks you at #5509 across all Steem accounts.
Your rank has not changed in the last three days.
In our last Algorithmic Curation Round, consisting of 115 contributions, your post is ranked at #46.
Evaluation of your UA score:
Feel free to join our @steem-ua Discord server